TFS practice problem of the week...

Professional Engineer & PE Exam Forum

Help Support Professional Engineer & PE Exam Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Slay the P.E.

Well-known member
Joined
Sep 9, 2017
Messages
404
Reaction score
157
Location
Arlington Heights, IL
A steam turbine with an isentropic efficiency of 76% admits steam at 100 psia, 750F. The turbine discharge is at 2 psia. The shaft power developed in kW per lbm/h of steam flowing through the turbine is most nearly:

(A) 0.08

(B) 0.10

(C) 0.27

(D) 262

 
Hi,

So this is what I got using Mollier 0.067kW time 3min 46 sec.

Using tables I got 0.077kW time 2min 24 seconds.

I think it made me faster on tables just because I already input the numbers, each step. OR maybe I am just slow in the chart.

 
Last edited by a moderator:
Hi,

So this is what I got using Mollier 0.067kW time 3min 46 sec.

Using tables I got 0.077kW time 2min 24 seconds.

I think it made me faster on tables just because I already input the numbers, each step. OR maybe I am just slow in the chart.
I used the chart and got it in about a minute. I think it helps because my super heated steam tables don't have 750 C so i would have to interpolate or estimate and estimating is easier for me with the chart.

 
I used the chart and got it in about a minute. I think it helps because my super heated steam tables don't have 750 C so i would have to interpolate or estimate and estimating is easier for me with the chart.
Yes, its just I am bad at the chart, I used the chart in the MERM appendix using only ruler, did not point my pencil or write a line since its not allowed during test, that's what I got from using chart, my estimate was h1=1405 and h2=1105 that't definitely not within 2% from the value calculated using tables. In this case, there are no other options so would choose A. 

 
Last edited by a moderator:
Oh crap I screw it up, was supposed to be about 1060 h2. Probably when I blinked it went up one line lol it should be same value 0.077kW using the chart.

 
Oh crap I screw it up, was supposed to be about 1060 h2. Probably when I blinked it went up one line lol it should be same value 0.077kW using the chart.
The merm chart was too small for me. I ended up downloading one online and printing it out and putting it in my resource binder.

 
I got (B).    h1=1403.4 and h2r=1039.8  h2i=925

Mine is wrong.  your chart reads h2i=1050

Yep.  Should be (A)...   I read the .2 psia curve initially, I think.

 
Last edited by a moderator:
Happy Friday. Here's a fresh practice problem for you.

A military jet flies at a speed of 495 miles/hour at an altitude of 49,000 feet. A commercial airplane is flying at the same Mach number as the military jet but at an altitude of 27,000 feet. A plot showing the variation of temperature with altitude in the atmosphere is provided for your potential use. The speed (ft/s) of the commercial jet is most nearly:

(A)  515

(B)  726

(C)  757

(D)  795

Variation of temperature with altitude in the U.S. standard atmosphere..png

 
Mach is speed relative to the speed of sound.  If two planes are flying at the same Mach number then they are flying at the same speed (independent of altitude). 

495 mph converts to 726 ft/s.

Answer is (B)

 
Mach is speed relative to the speed of sound.  If two planes are flying at the same Mach number then they are flying at the same speed (independent of altitude). 

495 mph converts to 726 ft/s.

Answer is (B)
I think not, temperature are different just have to equate both v1/(kgcRT1)^1/2=(v2/kgcRT2)^1/2

You get  v2

 
Last edited by a moderator:
I think not, temperature are different just have to equate both v1/(kgcRT1)^1/2=(v2/kgcRT2)^1/2

You get  v2
oops.  I forgot that the speed of sound varies with temp/changes in atmosphere.  I'm a structural guy.

 
Sure!!!  Where was this 2 years ago when I was studying for my exam????   BUT NO.....   Mike had to use the Black and White one and had to blow it up to 11X17 so his eyes wouldn't cross...
LOL

well, you know what will really suck? When the exam transitions to closed-book CBT next year. I dunno if the on-screen reference book will have a Mollier diagram, but if it does, just imagine people putting a ruler against the computer monitor... yikes 

 

Latest posts

Back
Top