Search the Community
Showing results for tags 'mechanical pe exam'.
Found 3 results
Whether you’re taking the Mechanical PE MDM exam for the first time or this is your “nth” attempt, I hope that my experiences make this journey a bit easier for you. First let me tell you a bit about myself to put things in perspective. I obtained my BSME degree in 1996 and throughout my career, I worked in the private sector for large High-Tech corporations so I never had a need to get the PE license. That changed when I decided to work for the government in search of job stability and a pension. From the get-go, I had no delusions that this would be an easy task, after all I rarely used the concepts I learned in college in my every-day job, perhaps with a few exceptions in the areas of materials, failure analysis and vibrations which is the reason I chose MDM over the other disciplines. Being out of school for nearly 21 years was definitely a handicap for me, but I was determined to take on the challenge. My “mission” to prepare for the PE exam started in July’16 and little did I know this would turn out to be an almost 2-year long endeavor. The First Time (Fall ’16): I enrolled in PPI’s refresher course and scored 38/80 (this is before the exam format change). I easily spent 300 hours studying but didn’t have time to do as many extra problems as I would’ve liked. Spent a lot of time re-learning engineering principles and I feel this hurt my speed during the exam. The Second Time (Spring ’17): I enrolled in PPI’s refresher course again (new instructor) taking advantage of their re-take policy (this was the first time after the exam format change). Again, I easily spent 300+ hours doing extra problems, had a study-buddy to help with the course load and felt much better after taking the exam. My score was 46/80 so I failed again. Completely devastated. The Third Time (Fall ’17): I stuck with Machine Design & Materials but decided to switch to Dr. Tom’s course (2nd time after the format change) and was very happy to see new material, new practice problems which I thought would give me more practice and help improve my speed during the exam. My score was 49/80, so still not enough to pass. The Fourth Time (April ’18) I decided I had already learned all there was to learn and embraced the fact that all I needed was more practice, practice, practice which in turn would give me speed and agility during the exam. I also had to make a decision as to what material I was going to study with, and it was pretty easy to come to the conclusion that PPI’s material, although not useless, was definitely not representative of NCEES type-questions (it’s good to establish foundational knowledge but that’s about the extent of it). Instead I opted to follow the Dr. Tom course outline one more time, BUT, I enhanced it with more practice problems that I found online. My most useful references during studying were (in order of preference): MERM 13th Edition: Follow the Dr. Tom MDM outline and make sure you read ALL THE CHAPTERS before watching the videos. His explanations will make more sense, trust me on that. NCEES practice exams: There are 2 out there, 2016 is the most recent but there is a 2011 version which has about 13 problems that are still relevant to our discipline. I suggest you search for it on line (all other problems are the same as in the 2016 version). Dr. Timothy Kennedy’s review book: You can find this on Amazon and although it may not be as detailed as MERM, there are LOTS of extra new problems that you can practice with. It’s about $40 bucks and well worth the money. 6-Min Solutions for MDM: Dr. Tom provides a recommendation for which problems to solve from this book from a total of 80. Lots of good material here. Do all the extras! EngProGuides Practice Exam: Runs about $35 and you can get it from their website http://www.engproguides.com/. Justin Kauwale the owner, is very responsive and will answer all your questions promptly via email. Scott Hart and Kevin Klein practice exam: Another Amazon purchase, this exam is harder than NCEES but some of the problems are definitely in line with what you can expect to see on the exam (about 60%). Machinery’s handbook: This will come in handy for the “supportive knowledge” portion of the exam. The welding section is also MUCH easier to understand compared to MERM. Lindeburg unit conversion book: Definitely a must, it’ll save you time during the exam especially with those pesky, hard to find conversions Oxford Dictionary of Mechanical Engineering: I was able to answer several questions from the practice exams using this book, I also used it at least twice during my last exam attempt. The Study Plan that helped me PASS the 4th time was: 1. Purchase the MDM review course from Dr. Tom and start as early as you can (at least 14 weeks prior to the exam). 2. If you are a repeat test taker, take a long, hard look at your diagnostic report from NCEES. Try to remember what areas gave you the most trouble during the exam and then spend extra time on those topics as you go through the course. If this is your first time taking the test, then simply move on to 3 below. 3. Make sure you read all MERM chapters relevant to each of the course topics BEFORE you watch the Dr. Tom videos. Do all assigned problems per section and then supplement with problems from Dr. Kennedy’s book as well as 6-min Solutions, this will reaffirm your knowledge of the subjects. For some reason the Economics chapter (74 in MERM) isn’t covered by Dr. Tom so make sure you read that, do the practice problems in Dr. Kennedy’s book as well. 4. Once you complete the Machine Design section of the course which is about half way through, you should have enough background to take your first practice test about 6 weeks prior to the actual exam. DO NOT WAIT UNTIL 2 weeks prior to the test to do this. The first time I took the exam I did everything PPI told me to and I realized I had made a terrible mistake by waiting to take the NCEES practice test until the very end of the course. It was too late to make a correction by then. This will give you a good idea of where you are knowledge wise so you can identify weak spots and make adjustments as necessary. Make sure you mimic actual test conditions to get a sense of what that 6-min. allowance per problem feels like. I’ve seen others here recommend the following strategy which totally works: a. As you read through each problem, if you know what they’re asking and feel fairly confident you can work it, do it. b. If you have an idea of how to work the problem but think it’ll take you some time to find the necessary equations, mark it a “2” and move on. c. If you have absolutely no idea how to answer the problem mark it a “3” and move on. d. On your 2nd pass answer all the problems you marked 2 (or as many as you can). e. On your 3rd pass answer all the problems you marked 3 (or as many as you can). f. You will probably make several passes before you answer all the problems but that’s OK, remember that this is about getting the low-hanging fruit FIRST, all problems are worth the same so leave the more difficult ones for the end. 5. After you evaluate the results of your first practice test, you will know what areas you need to beef up on and will be better prepared for the next one. I would recommend that you try to finish the course early so you have enough time to do the EngProGuides practice test next, about 3 weeks prior to the exam. 6. The last 2-3 weeks prior to the exam you should focus on doing nothing but problems until you’re blue in the face. Problem recognition is a must and this will only come through extensive practice. Be honest with yourself and time every problem you do so you can train your brain to work against the clock. I made several passes of the following during the home-stretch: a. NCEES practice exam (3 passes) b. EngProGuides (2 passes) c. Dr. Tom’s course problems (2 passes) d. 6-min. solutions (2 passes) e. Dr. Kennedy’s book (2 passes) f. Scott Hart and Kevin exam (1 pass) 7. The day before the exam, give yourself a break, DO NOTHING and just relax. My most useful references during the exam were.... 1. MERM 2. Binders from Dr. Tom’s course 3. Machinery’s Handbook 4. Lindbergh unit conversion book 5. Oxford Mechanical Engineering dictionary 6. Do not bring books to the exam you haven’t studied with, this will only eat up your valuable exam time! You will probably spend anywhere between 250-300 hours studying so make sure you develop a plan that works for you and stick with it. I know this is a lot to share but hopefully after reading this I will spare you the pain of having to take the PE exam more than once. Study hard because when you see the little green box with the word PASS in it, it’ll all be worth it !!! And last but not least, in the words of the great Jedi Master Yoda: “Do or do not, there is no Try…” Good luck!
Hi everyone! Now is your chance to save on PPI’s comprehensive live online review courses, featuring a passing guarantee. This limited time pricing for all-inclusive FE, PE, or SE review courses provides you with expert instruction and support as well as a full collection of best-selling review materials to ensure you have everything you need to prepare to pass. From now until December 3rd, save up to $550 on our exam review course packages.
Mechanical PE Sample Exam [$20] 40 Morning Session Exam Problems with Detailed Solutions [$20] 40 Afternoon Session HVAC and Refrigeration Exam Problems with Detailed Solutions [$35] 40 Morning and 40 Afternoon HVAC and Refrigeration Session Exam Problems with Detailed Solutions Engineering Pro Guides http://www.engproguides.com